Entries from September 2008 ↓

Question: Can I use a Boair 5 stage air filter with a geothermal system?  The unit is 8 1/2 years old.  I have a metal filter that you hose off just like the Boair 5 stage, but they said it would last 8 to 10 years.  My thermostat is showing it needs changed.  I did clean it and replaced it in the unit but it is still saying change.  Thank You.

Changing to a Boair 5 Stage Electrostatic Filter

If you are currently using some type of electrostatic air filter in your geothermal heat pump I see no reason not to use the Boair 5 Stage electrostatic filter instead.  They are one of the most efficient electrostatic furnace filters available.  However, without seeing your old filter, I can’t say if you need to replace it or not.

I looked at a friends heat pump the other day and he was using an electrostatic air filter with a metal frame and the filter was still in very good condition after 10 years of use.

There are Two Types of Filter Change Indicaters

Thermostat Filter Change Timers

1) This type has an electronic timer in the thermostat that is used only as a reminder to change your air filter at pre determined intervals.  Depending on the type of thermostat you are using the intervals can be based on hours of operation or days of operation.  These times are usually programmed into the thermostat when they are installed and can be adjusted later if necessary.

Every time the filter change indicator illuminates on the thermostat it must be reset so that the timing sequence begins again from zero.  Resetting these timers is typically done by pressing a button or a combination of buttons.  Sometimes they can be a bit tricky to figure out.  Every manufacturer has there own way of doing things.

These filter change indicators do no reset automatically, so you will have to reset it yourself.  If you are unsure how to reset it contact the manufacturer or a local contractor.  You may also be able to find this information by doing a search online for the manufacturer and model number of the thermostat.

If the thermostat will not reset and you are sure you are using the proper procedure, you will have to change the thermostat.  These filter change indicators are only reminders and do not indicate if the filter is actually dirty or not.  If the thermostat is working properly otherwise I would not worry about a faulty filter change indicator.  Simply replace or clean the filter every one to three months and you will be fine.

Filter Clog Switch

2) The second type of filter change indicator is the filter clog switch.  These are much better devices and are activated when the furnace filter or air conditioner filter becomes dirty.

Unfortunately these types of filter change indicators are not often used in residential heating and air conditioning equipment.  There is a higher cost associated with these filter change indicators and of course to be competitive manufacturers have to offer similar products.

These filter change indicators sense the air flow through the air handler and react to changes in air pressure within the air handler.  There are a couple of different ways that this can be done, but that is beyond the scope of this article.

Basically what happens is, as the filter becomes dirty it causes a restriction to air flow through the filter.  This restriction to air flow causes a pressure change that the filter change indicator (air flow switch) reacts to, telling you it is time to change your air filter because it is getting dirty.

There are Two Things That Can Cause This Type of Filter Change Indicator to Indicate a Dirty Filter Incorrectly

1) If the air flow switch is not calibrated properly it may indicate that the filter needs to be changed when it doesn’t or it may not indicate the filter is dirty at all, when it fact, it is time for it to be changed or cleaned.

2) The other thing that can cause this type of filter change indicator to give false readings and is relatively common in heat pumps and air conditioners that are have been in service for many years and systems that use inefficient filters, is a dirty evaporator coil.

Before making any changes to the settings of the air flow switch, inspect the evaporator coil and make sure it is not dirty and restricting air flow.  A dirty air filter and a dirty evaporator coil show the same symptoms, so if everything indicates a dirty air filter but you know it is clean, check the evaporator coil.

Question: How often do you need to change your air conditioning filter?

Changing your air conditioner filter or furnace filter is the most important maintenance task there is if you want to keep your equipment operating at maximum efficiency.  Allowing an air conditioner filter to become so dirty that it begins to restrict air flow can cause evaporator coils to ice up, operating efficiency will decrease and even prevent the unit from maintaining the desired space temperature.

The easy answer to this question is every three months and you should not have any problems.  But there are really many variables to consider when trying to provide an accurate answer to this question.  Often sales people can quote efficiency ratings or MERV ratings and provide you with their standard recommendation but they often don’t really understand how air conditioners operate.

Here are a couple of articles I wrote about this topic.  The first one I wrote today.  The second one I wrote some time ago but found it only after I wrote the one today.  Anyway, they are similar but each provide some different information.  Please leave comments or email questions if you have any.

When To Change Your Air Conditioner Filter
Selecting And Maintaining Your Air Conditioner Filter

Question: I have a Water Furnace and currently use a pleated filter with a MERV 5 rating.  how high can I go before I start restricting the flow too much and damage the system?

A Merv 5 filter is really not very efficient.  If you have a properly sized duct system and you change your air filter regularly I see no reason not to use an air filter with as high as a Merv 12 rating.  as Merv ratings increase so does restriction to air flow, so you always have to be careful.  The reason I mention a properly sized duct system is because if the duct system is undersized it will restrict air flow dramatically and is a common problem in many homes.  A very efficient air filter and an undersized duct system are not a good combination.

There are a couple of signs that may indicate an undersized duct system:

-  The air conditioner coil ices up when the filter becomes dirty.  Most systems will do this if the filter becomes extremely dirty but you should not have this problem if the filter becomes only moderately dirty and you change it regularly.

- Whistling sounds coming from around the air handler access panels can be an indication of an undersized duct system.  This can also indicate poorly fitting access panels.

- If your furnace trips of on the high limit switch, this could indicate an undersized duct system.

There are other things that could cause the problems listed above but they are also signs of restricted air flow.

If you have your equipment serviced regularly ask your contractor if the duct is sized properly.  Opinions vary among contractors regarding filters with high Merv ratings.  Your other option is to try a higher Merv rating and monitor equipment operation closely.

Question: What is the MERV Rating of the BoAir 5-Stage electrostatic filter?

The BoAir 5-Stage electrostatic filter like all electrostatic air filters doesn’t have a MERV rating. MERV ratings are only used to rate media types of air filters such as pleated filters and Hepa filters. But if you compare the Arrestance rating of the BoAir 5-Stage electrostatic filter, which is over 95%, the media type filters with similar Arrestance ratings it is equivalent to a Merv 6 or a Merv 8 filter.

A furnace filter with a Merv 8 rating is suitable for use in you air conditioning or heating system if you don’t suffer from allergies but if you require more efficient filtration to manage your allergies I would recommend a Merv 10 to 12 pleated filter.